Technology

Plastering details

joint to the ceiling will have methods and principles to do When plastering joints with the ceiling in the construction of a house บริษัทรับสร้างบ้าน  there must be a space for the ceiling deflection. The corner stop of the wall is attached to the steel bracket of the ceiling bracket. and must have additional details as follows

  • Plastered walls 2″ (51) thick.
  • Sealant with soundproofing material.
  • Edge finishing
  • Ceiling bracket
  • The truss base is attached to the truss structure.
  • Plastered metal grates
  • The main frame is attached to the ceiling.
  • Crosswise fixing the ceiling.
  • The upper wall is stretched with the steel ceiling frame.

At the end of the wall does not hit the ceiling

  • Steel to cover the end of the wall. and the steel grating is attached to the double gutter steel frame.

joint with metal jamb

  • Fasten the dowel embedded in the transom to the metal frame.
  • Frame pressed with grout. to increase strength
  • The front of the wall is always with the jamb edges.

soundproof wall

  • Flexible clip.
  • Plastered steel grating
  • Plastering gypsum board

joint with metal jamb

  • Prefabricated wall panels
  • Attach the dowel embedded in the transom to the steel grating and the double gutter steel frame.
  • Metal frame pressed with reinforced grout.
  • Similar to the picture above.
  • Plastering around the edge of the jamb 1⁄8″ (3), the face is not equal to the jamb’s edge.

joints with wooden frames

  • Cut the trowel to prevent the plaster from sticking to the cleat.
  • The cleat serves to help determine the thickness of the plaster. and the scope of plastering

joint to the floor

  • The cornice at the foot of the metal wall, the surface is the same as the wall.
  • Steel clip to fix the cornice on the wall.
  • Flexible wall cornice.
  • Wood cleats are attached to the truss frame.
  • Mounting clips or brackets are attached to the floor.
  • The cornice at the foot of the metal wall, the surface is the same as the wall.
  • Sealant with soundproof sealant.
  • The stop edge of the base of the wall between the two types of materials.
  • Edge finishing (optional eyebrow device)
  • wall surface

Plastering the ceiling

If the steel grating or gypsum board is directly attached to the joist or truss Plaster or gypsum plaster can crack due to the body or the annex of the joist or rough. The home builder company รับสร้างบ้าน may use protection methods by requiring that the deflection distance of the joist or truss in the truss line must not exceed 1/360 of the length of the joist. Or install a suspended ceiling from the floor or roof structure instead without attaching to the floor or roof. This hanging method allows the ceiling to move relatively freely. It also allows for a gap on the ceiling for the installation of the system forks.

  • Steel hanging from the ceiling.
  • Main gutter steel 1½” (38) spaced until 4’0″ (1,220)
  • Crosswise ¾” (19) is attached to the main gutter. Please refer to the table in Section 10.03 for the distance.
  • Steel grating is attached to the steel frame at every 6″(150) distance.
  • Joints in walls and ceilings or walls.

non-adherent

  • Edge finishing
  • Not more than 6″ (150)
  • 1½” steel bar (38)
  • ¾” (19) crossbar
  • wall material

Plastering in restricted conditions

  • 3″ (75) steel grids laid over each other.
  • Continuous plastering requires a strong supporting structure.

seam to break

Plastering the ceiling should have at least 30′ (9,145) joint gaps in each direction. and the contiguous area should not exceed 900 ft² (84 m²) without cracking joints. This joint will help prevent cracking on the plaster surface. due to shrinkage from temperature changes or structural stress especially with a wide plastered area

  • Expansion joints
  • Gypsum board is attached to the frame.
  • Leakage joints on ceilings or walls.
  • Joints for cracks in corners.

Plastering on the wall, construction material and concrete wall

Plastering on the plasterboard surface A panel or grating material should be used to hold the plaster in the following cases:

  • The surface of the wall material is not suitable for direct plastering.
  • Moisture has passed through the wall from the other side.
  • Need to have space inside for insulating material.
  • Need a wall surface that has a little flexibility. To help keep the sound by using the internal space behind the panel • Non-flexible rough.
  • Steel gutter ¾” (19)
  • Flexible mounting clip
  • Where soundproofing is required, the supports are attached to the wall with a flexible clip between the plaster and the wall.
  • Vertical reinforcement
  • Use horizontal reinforced steel gutter. for strength and help support the vertical frame
  • Wooden or metal supports. It can be installed horizontally or vertically.
  • In the case of plastering on the surface of the plasterboard material Plastering method and spacing of the truss
  • The dowels attached to the wall should be of the type that can be adjusted according to the depth of the gap.

Plastering directly on the wall

  • Usually, two layers of plaster are applied to the wall. The plaster is approximately 5⁄8″ (16) thick.
  • Plastering is applied directly to the wall surface if the wall surface is rough and water resistant enough to adhere to the plaster.
  • Should mix substances or solutions to increase adhesion. to help the plaster adhere to the wall better especially for walls that are solid or not waterproof, such as concrete.
  • Corner brow accessory.
  • Corner accessories
  • Usually measures 5⁄8″ (16).

Related Articles

Leave a Reply

Back to top button